diff --git a/doc/sections/ex-gwf-maw-collector.tex b/doc/sections/ex-gwf-maw-collector.tex index 7415c0a0..7a4f2d69 100644 --- a/doc/sections/ex-gwf-maw-collector.tex +++ b/doc/sections/ex-gwf-maw-collector.tex @@ -1,17 +1,17 @@ \section{Radial Collector Well} % Describe source of problem -A radial collector well, also called a Ranney well, is a central caisson with several horizontal laterals that radiate outward near the base of an aquifer. The caisson is a watertight shaft that is not screened, so water enters the well only through the laterals, and the laterals give the well a large area of contact with the aquifer. A radial collector well can yield much more water than a vertical well for the same drawdown. This example represents a radial collector well as a single multi-aquifer well in the \mf Multi-Aquifer Well (MAW) Package, with one horizontal connection to each cell a lateral passes through, using the NON\_VERTICAL\_WELLS option. A transient simulation that includes storage in the well compares the head in the well with the laterals represented as horizontal connections and as thin vertical screens. +A radial collector well, also called a Ranney well, is a central caisson with several horizontal laterals that radiate outward near the base of an aquifer. The caisson is a watertight shaft that is not screened, so water enters the well only through the laterals, and the laterals give the well a large area of contact with the aquifer. A radial collector well can yield much more water than a vertical well for the same drawdown. This example represents a radial collector well as a single multi-aquifer well in the \mf Multi-Aquifer Well (MAW) Package, with an inactive connection for the caisson and one horizontal connection to each cell a lateral passes through, using the NON\_VERTICAL\_WELLS option. A transient simulation that includes storage in the well compares the head in the well with the laterals represented as horizontal connections and as thin vertical screens. \subsection{Example Description} % spatial discretization and temporal discretization The aquifer is 50 $m$ thick and is represented by one layer of 41 rows and 41 columns that are 25 $m$ wide. Horizontal and vertical hydraulic conductivity are 25 $m/d$ and specific storage is $1 \times 10^{-4}$ $1/m$. Head is 50 $m$ at the start of the simulation and is held at 50 $m$ in the cells around the edge of the domain. Model parameters are summarized in table~\ref{tab:ex-gwf-maw-collector-01}. -The caisson is in the center cell of the domain and four laterals extend 12 cells, 300 $m$, north, south, east, and west from it (fig.~\ref{fig:ex-gwf-maw-collector-well}). The caisson is not screened, so it has no connection, and the well exchanges water with the aquifer only through connections 1 to 48, one for each of the 48 cells the laterals pass through. The connections of each lateral are numbered in order outward from the caisson. The laterals are horizontal boreholes centered 2 $m$ above the base of the aquifer. The aquifer is confined and represented by a single layer, so the elevation of the laterals places the screens within the layer but does not affect the simulated heads. The well radius is 0.15 $m$, the radius of the laterals, and a filter pack with a hydraulic conductivity of 25 $m/d$ extends to a radius of 0.3 $m$. The MAW Package uses one radius for every connection of a well and calculates storage in the well from the same radius, so the storage represented is that of a borehole the size of a lateral rather than that of the larger caisson. The MEAN conductance equation is used for every connection, because the radial conductance equations assume that flow converges on the well in the horizontal plane, while flow to a horizontal lateral converges in a vertical plane. +The caisson is in the center cell of the domain and four laterals extend 12 cells, 300 $m$, north, south, east, and west from it (fig.~\ref{fig:ex-gwf-maw-collector-well}). The caisson is connection 1, a vertical connection to the center cell over the full thickness of the aquifer. The caisson is not screened, so the CONNECTION\_STATUS setting makes the connection inactive, and the well exchanges water with the aquifer only through connections 2 to 49, one for each of the 48 cells the laterals pass through. The connections of each lateral are numbered in order outward from the caisson. The laterals are horizontal boreholes centered 2 $m$ above the base of the aquifer. The aquifer is confined and represented by a single layer, so the elevation of the laterals places the screens within the layer but does not affect the simulated heads. The well radius is 0.15 $m$, the radius of the laterals, and a filter pack with a hydraulic conductivity of 25 $m/d$ extends to a radius of 0.3 $m$. The MAW Package uses one radius for every connection of a well and calculates storage in the well from the same radius, so the storage represented is that of a borehole the size of a lateral rather than that of the larger caisson. The MEAN conductance equation is used for every connection, because the radial conductance equations assume that flow converges on the well in the horizontal plane, while flow to a horizontal lateral converges in a vertical plane. \begin{StandardFigure}{ - Oblique view of the radial collector well and the central 29 rows and 29 columns of the model, from 35 degrees above the horizontal and 45 degrees from the laterals. The model grid is drawn at the elevation of the laterals, 2 $m$, and black lines are the top and bottom of the aquifer. Numbers are the first and last well connection of each lateral. The caisson is enlarged to be visible and is not to scale. Vertical exaggeration is 5. + Oblique view of the radial collector well and the central 29 rows and 29 columns of the model, from 35 degrees above the horizontal and 45 degrees from the laterals. The model grid is drawn at the elevation of the laterals, 2 $m$, and black lines are the top and bottom of the aquifer. Numbers are well connections: the caisson, connection 1, which is inactive, and the first and last connection of each lateral. The caisson is enlarged to be visible and is not to scale. Vertical exaggeration is 5. }{fig:ex-gwf-maw-collector-well}{../figures/ex-gwf-maw-collector-well.png} \end{StandardFigure} @@ -28,7 +28,7 @@ \subsection{Example Results} Simulated steady-state head is shown in figure~\ref{fig:ex-gwf-maw-collector-map}. The head in the well is 46.99 $m$, 3.01 $m$ below the starting head and 0.014 $m$ below the lowest head in the aquifer, at the caisson and the first cell of each lateral. Drawdown extends along each lateral to its end, and the head contours are elongated along the laterals, because the well withdraws water from every cell a lateral passes through. \begin{StandardFigure}{ - Simulated steady-state head for a radial collector well pumping 25,000 $m^3/d$, with the laterals represented as horizontal connections. Contours are labeled in meters. The open circle is the unscreened caisson, which has no connection, red cells are connected to the laterals, and gray cells have a constant head of 50 $m$. + Simulated steady-state head for a radial collector well pumping 25,000 $m^3/d$, with the laterals represented as horizontal connections. Contours are labeled in meters. The open circle is the unscreened caisson, which has an inactive connection, red cells are connected to the laterals, and gray cells have a constant head of 50 $m$. }{fig:ex-gwf-maw-collector-map}{../figures/ex-gwf-maw-collector-map.png} \end{StandardFigure} diff --git a/scripts/ex-gwf-maw-collector.py b/scripts/ex-gwf-maw-collector.py index f0f8d2a9..6eacfc14 100644 --- a/scripts/ex-gwf-maw-collector.py +++ b/scripts/ex-gwf-maw-collector.py @@ -4,11 +4,11 @@ # horizontal laterals that radiate outward near the base of an aquifer. The # caisson is not screened, so water enters the well only through the laterals. # This example represents a radial collector well as a single multi-aquifer well -# with one horizontal connection to each cell a lateral passes through and no -# connection for the caisson. A steady-state simulation shows the head field -# around the well, and a transient simulation of pumping and recovery, with -# storage in the well, compares the well head with the laterals represented as -# horizontal connections and as thin vertical screens. +# with an inactive connection for the caisson and one horizontal connection to +# each cell a lateral passes through. A steady-state simulation shows the head +# field around the well, and a transient simulation of pumping and recovery, +# with storage in the well, compares the well head with the laterals +# represented as horizontal connections and as thin vertical screens. # ### Initial setup # @@ -89,9 +89,9 @@ # Static temporal data used by TDIS file tdis_ds = ((perlen, nstp, tsmult), (perlen, nstp, tsmult)) -# The caisson is in the center cell and has no connection. Each lateral is a -# horizontal borehole near the base of the aquifer, so its connection is -# screened over one well diameter. +# The caisson is in the center cell and its connection is inactive. Each +# lateral is a horizontal borehole near the base of the aquifer, so its +# connection is screened over one well diameter. caisson = (0, nrow // 2, ncol // 2) # Every scenario is in its own folder, so the flow model has one name @@ -171,18 +171,19 @@ def build_models(name, transient=True, horizontal=True): chdspd.append([(0, i, j), strt]) flopy.mf6.ModflowGwfchd(gwf, stress_period_data=chdspd, pname="CHD") - # one well head for the caisson and the four laterals. The caisson is not - # screened, so it has no connection. Each lateral cell is a separate - # connection, horizontal (90 degrees) and one cell long, when the length - # correction is applied, or a vertical screen one well diameter long when - # it is not. - connectiondata = [] + # one well head for the caisson and the four laterals. The first connection + # is the unscreened caisson, a vertical connection that is inactive. Each + # lateral cell is a separate connection, horizontal (90 degrees) and one + # cell long, when the length correction is applied, or a vertical screen one + # well diameter long when it is not. + connectiondata = [[0, 0, caisson, top, botm, k_skin, skin_radius]] angledata = [] - for icon, cellid in enumerate(lateral_cellids()): + for icon, cellid in enumerate(lateral_cellids(), start=1): connectiondata.append( [0, icon, cellid, screen_top, screen_bot, k_skin, skin_radius] ) angledata.append([0, icon, 90.0, delr]) + caisson_status = [0, "connection_status", 0, "inactive"] rate = transient_rate if transient else steady_rate maw_kwargs = { "save_flows": True, @@ -193,12 +194,12 @@ def build_models(name, transient=True, horizontal=True): } if transient: maw_kwargs["perioddata"] = { - 0: [[0, "rate", -rate]], + 0: [caisson_status, [0, "rate", -rate]], 1: [[0, "rate", 0.0]], } maw_kwargs["observations"] = {f"{gwf_name}.maw.obs.csv": [("head", "head", 1)]} else: - maw_kwargs["perioddata"] = {0: [[0, "rate", -rate]]} + maw_kwargs["perioddata"] = {0: [caisson_status, [0, "rate", -rate]]} if horizontal: maw_kwargs["non_vertical_wells"] = True maw_kwargs["angledata"] = angledata @@ -316,7 +317,8 @@ def plot_well_schematic(silent=True): ax.zaxis.set_rotate_label(False) ax.set_zlabel("Elevation,\nin meters", labelpad=10, rotation=90) - # connection numbers: the first and last connection of each lateral + # connection numbers: the caisson, the first connection of each lateral, + # and every tenth connection label_connections(ax, xc, yc) handles = [ Line2D([], [], color="red", lw=2.0, label="Lateral"), @@ -370,7 +372,9 @@ def to_points(xy): }, "zorder": 10, } - icon = 1 + ax.annotate("1", xy=project(xc, yc, top), xytext=(0.0, 12.0), **text_kwargs) + + icon = 2 for di, dj in lateral_directions: # connections are labeled below the lateral on the page, between the # lateral and the outline of the aquifer; the first connection is